How to remove the Arlo Video Doorbell from the wall Mount

The Arlo Video Doorbell is now becoming one of the must-have security gadgets at home. However, not like the ordinary security cameras and other doorbells, the Arlo Video Doorbell is flexible and allows you to move it to any other location in your house without needing assistance from a technician. In case you recently installed your doorbell and want to transfer it to another location, we have put together a step-by-step guide to show you how to remove the Arlo Doorbell from the wall mounting and relocated it to another area.

How to remove the Arlo video Doorbell from the wall mount plate

During the installation process of the Arlo Doorbell, you noticed that you had to install the mounting plate on the wall. Then, you rested your doorbell on this mounting plate without the need to screw it. Therefore, while removing it, you still do it without unscrewing anything or disconnecting any wires.

You will only need the release pin that came with your Arlo Video Doorbell or a straightened paperclip to assist you in removing it.
Get hold of the release pin that came along with your Arlo video Doorbell
Now insert this pin into the pinhole at the top or bottom of the doorbell mount
Once you have done that correctly, you will hear a clicking sound and your doorbell will be released from the mount.
Finally, just pull off the doorbell from the mount and that is.

How to completely remove the Arlo video Doorbell from the wall

In case you just wanted to service your doorbell, or do some kind of maintenance, repair, etc, the above steps are enough. However, if you wanted to relocate your Arlo video Doorbell to another area, then it would need a complete removal of the mounting plate and the wires themselves.

Whether it is a wired or wirelesses Arlo Video Doorbell, here is how you can safely remove it from the wall for relocation. However, ensure that the Arlo Video Doorbell is powered off. You can do this by disconnecting it from its power source then proceed with the steps below:

Step One: Disconnect the wiring (If Applicable)

If your Arlo Video Doorbell is hardwired to your home’s electrical system, you’ll need to disconnect the wiring before removing it. Then, carefully unscrew the wire nuts or terminal screws holding the wires in place. Finally, gently pull the wires away from the doorbell, taking care not to damage them.

Step Two: Uninstall the Mounting Plate

The Arlo Video Doorbell is typically mounted to a mounting plate that is attached to the wall or doorframe. So, you will need to use a screwdriver to remove any screws or fasteners securing the mounting plate to the surface, detach it and set it aside.

Step Three: Fill Holes (If Desired):

If the removal of the Arlo Video Doorbell leaves behind any holes in the wall or doorframe, you may choose to fill them with spackling compound or suitable filler. Allow the filler to dry completely, then sand it smooth and touch up the paint as needed to match the surrounding surface.

Step Four: Clean and relocate

Once the Arlo Video Doorbell is removed, clean it and any associated parts with a soft, dry cloth. And if you want to relocate it to another area of your house, kindly follow the installation process in our previous guide.

Frequently Asked Questions

How do you remove Arlo camera from mount?

To remove Arlo camera from mount, simply Get hold of the release pin that came along with your Arlo video Doorbell >>> Insert the pin into the pinhole at the top or bottom of the doorbell mount >>> You will hear a clicking sound and your doorbell will be released from the mount >>> Just pull off the doorbell from the mount and that is.

How to factory reset Arlo doorbell?

You can reset your Arlo back to factory settings by simply: Press Reset button on the back of the Arlo SmartHub or Base Station for 10 seconds >>> Wait for the LED on the front of the Arlo SmartHub to light >>> When it stops, the reset process is complete.

How do I reset my Arlo remotely?

You can also reset your Arlo video doorbell remotely using the mobile app in case your doorbell is online. To do this, simply Open the Arlo app on your mobile device >>> Go to Device setting >>>Tap my Devices >>> Select the Video Doorbell >>> Tap Remove Device to successfully reset your doorbell.

How to remove Arlo doorbell without release pin?

To remove Arlo camera from mount without release pin, simply use a straightened paperclip >>> Insert the straightened paperclip into the pinhole at the top or bottom of the doorbell mount >>> You will hear a clicking sound and your doorbell will be released from the mount >>> Just pull off the doorbell from the mount and that is.

How do I reset my Arlo remotely?